Stihl 08 Workshop Service Manual Repair
Stihl 08 Workshop Manual for the Repair and service of the Stihl 08 chainsaw (08). The PDF workshop service manual has accurate, easy to understand information and diagrams to help repair and service, information to help you to troubleshoot, repair and fix the Stihl 08 chainsaw (08). View pages online or download a complete PDF service manual that you can easily save, print or view on any device. This complete PDF manual is an Instant download.
Husqvarna Stihl 08 Workshop Service Manual Contents
Contents, Introduction, Safety Regulations, Symbols, Technical data, Service tools, Service data, Safety equipment, Starter, Electrical system, Centrifugal clutch, Lubrication system, Carburetor, Tank unit, Anti-vibration system, Piston and cylinder, Crankcase and crankshaft, Troubleshooting, Repair Instructions.
Carburetor – General Chainsaw Adjustment
Adjusting the carburettor involves adjusting the engine to the local conditions e.g. climate, altitude, fuel and type of two-stroke oil. The carburettor is equipped with three adjustment options.
L = Low speed jet
H = High speed jet
T = Idling adjustment screw
The L and H jets adjust the fuel flow to match the airflow that the throttle valve opening allows. Turning them clockwise makes the fuel/air mixture weaker (less fuel in relation to the amount of air) and turning them anti-clockwise makes the fuel/air mixture richer. A weak mixture increases the engine speed and a rich mixture decreases the engine speed. The T screw controls the throttle position when idling. Turning the T screw clockwise gives faster idling; turning it anti-clockwise lowers idling speed (see manual for complete guide).
Carburetor Type: Tillotson HL-166A, B, HL-292C series
See the complete Stihl 08 S service workshop manual, carburetor manual, parts list, operator manual and technical supplements PDF downloads, also the repair and service articles available on this website for more information on how to service, repair and find parts for the chainsaw.
Stihl 08 Chainsaw Specifications
SERIES OR ASSEMBLY NUMBER: 1108
ENGINE DISPLACEMENT: 56 ccm (3.39 cu. in.), prior to 1969 displacement was 48 ccm (3.2 cu. in.)
CYLINDER BORE:47 mm (1.85 in.) early version 44 mm (1.73 in.)
PISTON STROKE: 32 mm (1.26 in.)
CYLINDER TYPE: Aluminum with a chrome-plated bore
INTAKE METHOD: Piston ported
CHAIN BRAKE: none
DRIVE TYPE: Direct
MAGNETO TYPE: Bosch flywheel type
CARBURETOR: Tillotson HL-166A, B, HL-292C series
MAJOR REPAIR KIT: RK-88HL for HL-166A, RK-114HL for HL-166B, HL-292C
MINOR REPAIR KIT: DG-5HL for all
AIR FILTER SYSTEM: Nylon mesh element
STARTER TYPE: Automatic rewind (Fairbanks Morse type)
OIL PUMP: Automatic
MAXIMUM ENGINE RPM: 7,000
IGNITION TIMING: 2 mm (0.08 in.) before TDC
BREAKER POINT SETTING: 0.4 mm (0.016 in.)
FLYWHEEL/COIL AIR GAP: Position is fixed
SPARK PLUG TYPE: Bosch W175T1
SPARK PLUG GAP: 0.51 mm (0.020 in.)
CRANKSHAFT MAIN BEARINGS: Ball
FUEL TANK CAPACITY: 750 ml (1.54 pints)
FUEL OIL RATIO: 20:1 after break-in
RECOMMENDED FUEL OCTANE: Regular
MIX OIL SPECIFICATION: Castrol 2-stroke SAE 40
CHAIN PITCH: .404 in.
SHORTEST GUIDE BAR SUPPLIED: 33 cm (13 in.)
LONGEST GUIDE BAR SUPPLIED: 53 cm (21 in.)
Stihl 08 Service Workshop Manual PDF
* Online preview
There are no reviews yet.