Stihl 08 S Parts List

$0.00

Stihl 08s parts list to view online or download and print. Diagrams and part numbers. Full PDF

Stihl 08 s Parts List Identification

Stihl 08 s Parts List for the correct identification of all component parts of the Stihl 08s chainsaw. PDF full version download available, containing clear diagrams and information to assist in the chainsaw workshop parts identification. Clear parts numbers lookup and diagrams. The service manual is also available from this website.

Contents of Stihl 08 S Parts List

Introduction, Specifications, Clutch, Engine, Cutting tool drive, Support frame, Special servicing tools and aids, Ignition system, Rewind starter, Throttle control, Fuel system, Carburettor, Av system, Shaft.

Language: English
File Format: PDF -read and print from any computer or device, mobile ready

Stihl 08S Chainsaw Specifications

MANUFACTURED BY: STIHL ANDREAS MASCHINENFABRIK STUTTGART, GERMANY
SERIES OR ASSEMBLY NUMBER: 1108
YEAR INTRODUCED: 1965
ENGINE DISPLACEMENT: 56 ccm (3.39 cu. in.), prior to 1969 displacement was 48 ccm (3.2 cu. in.)
NUMBER OF CYLINDERS: 1
CYLINDER BORE: 47 mm (1.85 in.) early version 44 mm (1.73 in.)
PISTON STROKE: 32 mm (1.26 in.)
CYLINDER TYPE: Aluminum with a chrome-plated bore
INTAKE METHOD: Piston ported
WEIGHT:
8.4kg
OPERATOR CONFIGURATION: One Man operation
HANDLEBAR SYSTEM: Rigid
CHAIN BRAKE: none
CLUTCH: Centrifugal
DRIVE TYPE: Direct
CONSTRUCTION: Die-cast magnesium
MAGNETO TYPE: Bosch flywheel type
CARBURETOR: Tillotson HL-166A, B, HL-292C series
MAJOR REPAIR KIT: RK-88HL for HL-166A, RK-114HL for HL-166B, HL-292C
MINOR REPAIR KIT: DG-5HL for all
AIR FILTER SYSTEM: Nylon mesh element
STARTER TYPE: Automatic rewind (Fairbanks Morse type)
OIL PUMP: Automatic
MAXIMUM ENGINE RPM: 7,000
IGNITION TIMING: 2 mm (0.08 in.) before TDC
BREAKER POINT SETTING: 0.4 mm (0.016 in.)
FLYWHEEL/COIL AIR GAP: Position is fixed
SPARK PLUG TYPE: Bosch W175T1
SPARK PLUG GAP: 0.51 mm (0.020 in.)
CRANKSHAFT MAIN BEARINGS: Ball
FUEL TANK CAPACITY: 750 ml (1.54 pints)
FUEL OIL RATIO: 20:1 after break in
RECOMMENDED FUEL OCTANE: Regular
MIX OIL SPECIFICATION: Castrol 2-stroke SAE 40
CHAIN PITCH: .404 in.
CHAIN TYPE: Oregon Chipper
SHORTEST GUIDE BAR SUPPLIED: 33 cm (13 in.)
LONGEST GUIDE BAR SUPPLIED: 53 cm (21 in.)
COLOUR SCHEME: Grey with Red air filter cover/rear handle

Stihl 08s Carburetor Settings

Verify there is a spark

– High/low needle initial settings: Turn in until they lightly touch the seats then turn them out 1-1/2 turns each.

– Check the choke slide to ensure it is engaging the coke linkage

– Proper starting procedure:
A – Slide the choke to the rear/on position.
B – Set the throttle to half throttle. (Squeeze the trigger & hold it while you push in the locking button on the side. Hold the locking button in while you release the trigger.)
C – If the saw hasn’t been run recently, you can take the air filter off & pour a small amount of mixed fuel into the carburetor before trying to start it.

If it starts but doesn’t keep running or won’t start back up, the vent may be plugged. The vent is a short piece of hose with a set screw pushed 3-4 threads into it. Do NOT screw it in. If it is screwed in, the threads will cut into the tubing creating a seal which will prevent fuel from reaching the carburetor due to a vacuum.

These are fairly simple chainsaws.

Stihl 08s Parts List PDF

* Online preview