Stihl 017 Specifications
Stihl 017 Specifications for Stihl 017 chainsaw, Find the specs information for the Stihl chainsaw including engine, fuel ignition system and cutting attachments.
Stihl 017 Specifications Engine
STIHL single-cylinder two-stroke engine with special
impregnated cylinder bore
Displacement: 30.1 cm3 (1.84 cu.in)
Bore: 37 mm (1.46 in)
Stroke: 28 mm (1.10 in)
Compression ratio: 9.5 :1
Engine power: 1.2 kW (1.6 bhp)
Max. torque: 1.5 Nm (1.1 lb.ft), at n = 5500 rpm
Mean idle speed: 3,200 rpm
Main bearings: Two deep-groove ball bearings
Big end bearing: Cylinder rollers, (cageless)
Small end bearing: Needle cage
Piston pin diameter: Ø 8 mm (0.3 in)
Connecting rod length: 51 mm (2 in)
Rewind starter: Pawl system
rope rotor: min. 1/2 turn
Starter rope: 3.0 mm (0.12 in) diameter, 800 mm (31.5 in) long
Clutch: Centrifugal clutch without linings
Diameter: 65 mm (2.56 in)
Clutch engages at: 4,100 rpm
Crankcase leakage test: at gauge pressure: 0,4 bar (5.8 psi), under vacuum: 0,4 bar (5.8 psi)
Fuel System
Carburetor: Diaphragm carburetor
Standard setting: adjusting screw L: approx. 1 turn open
Carburetor leakage test at gauge pressure: 0.4 bar (5.8 psi)
Fuel tank capacity: 0.25 l (0.53 US pt)
Octane number: min. 90 RON (USA/CAN: pump octane min. 87 unleaded)
Fuel mixture: Regular brand-name gasoline and two-stroke engine oil
Mix ratio: 50:1 with STIHL 50:1 two-stroke engine oil 25:1 with other brand-name, two-stroke, air-cooled engine oils
Air filter: Felt element
No H screw. Maximum engine RPM is permanently set by fixed jet (not adjustable)
Carburetor with balanced idle system with only one adjusting screw (LD)
Ignition System
Type: Electronic magneto ignition (breakerless) with integral trigger unit
Air gap: 0.15 – 0.30 mm (0.006-0.012 in)
Ignition timing: 1.0 – 1.6 mm (0.04-0.063 in) B.T.D.C. at 8,000 rpm
Spark plug (suppressed): CHAMPION RCJ 6Y, BOSCH WSR 6 F
Electrode gap: 0.5 mm (0.020 in)
Spark plug thread: M14 x 1.25
Length of thread: 9.5 mm (0.37 in)
Heat range: 200
Cutting Attachment
Guide bars: STIHL Rollomatic with nose sprocket
Bar tail: 3005
Bar lengths: 30 and 35 cm (12 and 14 in)
Oilomatic chain: 3/8″ (9.32 mm) Picco-Micro Mini
Chain sprockets: 6-tooth spur sprocket for 3/8″ Picco pitch
Chain speed: 18.6 m/s (61 ft/sec) at 10,000 rpm (with 6-tooth 3/8″ P sprocket)
Chain lubrication: Speed-controlled reciprocating oil pump, no oil feed at idle speed
Oil tank capacity: 0.15 l (0.32 US pt)
Stihl 017 Special Accessories
For User STIHL repair kit 1130 900 5000
For Service Carburetor parts kit 1130 007 1060
Stihl 017 Specifications Tightening Torques
Plastoform screws are used for polymer components and “DG” screws for light metal components. These screws form a permanent thread when they are installed for the first time. They can be removed and installed as often as necessary without detrimentally affecting the strength of the screwed assembly, providing the specified tightening torque is observed. For this reason it is essential to use a torque wrench.
Carburetor Manuals HERE and a Stihl 017 chainsaw workshop manual HERE. Stihl Parts list HERE a chainsaw search (magnifier icon) at top and bottom of this page, as well as a chainsaw repair help question and answer page HERE.