Stihl 019 T Specifications

Stihl 019 T Specifications

Stihl 019 T Chainsaw Specifications

Stihl 019 T Specifications for Stihl 019 T chainsaw, Find the specs information for the Stihl chainsaw including engine, fuel ignition system and cutting attachments.

Stihl 019 T Specifications Engine

Engine

STIHL single cylinder two-stroke engine with special impregnated cylinder bore.

Displacement: 35.2 cm3 (2.15 cu.in)
Bore: 40 mm (1.57 in)
Stroke: 28 mm (1.10 in)
Engine power to ISO 8893: 1.2 kW (1.6 bhp)
Max. engine speed with bar and chain: 12,000 rpm
Idle speed: 2,800 rpm
Bearings: Crankshaft supported in heavy duty ball bearings, needle cages on small and big ends.
Piston pin diameter: 8 mm (0.3 in)
Connecting rod length: 51 mm (2 in)
Rewind starter: Single pawl system
Reserve pull on rope rotor: min. 1/2 turn
Starter rope: 3.0 mm (0.12 in) diameter, 800 mm (31.5 in) long
Clutch: Centrifugal clutch without linings
Diameter: 64 mm (2.52 in)
Clutch engages at: 3,700 rpm
Crankcase leakage test at gauge pressure: 0.5 bar (7.25 psi)
under vacuum: 0.4 bar (5.8 psi)

Fuel System

Carburetor: Diaphragm carburetor
Standard setting High speed screw H: Open approx. 1 turn, Low speed screw L: Open approx. 1 turn.
Carburetor leakage test at gauge pressure: 0.4 bar (4.8 psi)
Fuel tank capacity: 0.29 1 (0.61 US pt)
Octane number: min. 90 RON (US/CAN: pump octane min. 87 unleaded)
Fuel mixture: Regular brand-name gasoline and two-stroke engine oil
Mix ratio: 1:50 with STIHL 50:1 two-stroke engine oil, 25:1 with other brand-name
two-stroke, air-cooled engine oils
Air filter: Felt element

Ignition System

Type: Electronic magneto ignition (breakerless) with integral trigger unit
Air gap: 0.25 mm (0.010 in)
Ignition timing: 1.6 – 2.3 mm (0.063-0.091 in), B.T.D.C. at 8,000 rpm
Spark plug (suppressed): NGK BPMR 7 A or CHAMPION RCJ6Y
Electrode gap: 0.5 mm (0.02 in)
Spark plug thread: M14x1.25
Length of thread: 9.5 mm (0.37 in)

Cutting Attachments

Oilomatic chain: 9.32 mm (3/8″) Picco-Micro-Mini
Chain sprocket: 7-tooth 3/8″ P spur sprocket
Chain speed: 21.7 m/s (71.2 ft/sec) at 10,000 rpm
Chain lubrication: Speed-controlled reciprocating oil pump. No oil feed at idle speed.
Oil delivery rate: Adjustable 5 – 9 cm3/min (0.17 – 0.30 fl.oz/min)
Oil tank capacity: 0.16 l (0.34 US pt)

Special Accessories

For User

STIHL repair kit 1132 900 5000
6-tooth 3/8″ P spur sprocket 1123 640 2005
8-tooth 1/4″ spur sprocket 1123 640 2010
ElastoStart 0000 190 3400

For Service

Carburetor parts kit 1132 007 1060

Tightening Torques

Plastoform screws are used for polymer components and “DG” screws for light metal components. These screws form a permanent thread when they are installed for the first time. They can be removed and installed as often as necessary without detrimentally affecting the strength of the screwed assembly, providing the specified tightening torque is observed.
For this reason it is essential to use a torque wrench when adjusting any correct Stihl 019 T Specifications.

More Stihl 019 T Specifications information can be found in Carburetor Manuals HERE and a Stihl 019T chainsaw workshop manual HERE. Stihl Parts list HERE a chainsaw search (magnifier icon) at top and bottom of this page, as well as a chainsaw repair help question and answer page HERE.