Stihl MS 211 Chainsaw Specifications
Stihl MS 211 Specifications for the Stihl MS211 chainsaw. Find detailed specs information for the Stihl chainsaw including engine, fuel system, Carburetor, ignition system, chain lubrication,Torque settings and cutting attachments.
Including models MS211 Z and MS211 C.
Stihl MS 211 Chainsaw Specs
Stihl MS 211 Specifications Carburetor
Replace carburetor with Zama Carb: C1Q-S119 (MS211 and MS211 Z), C1Q-S120 (MS211 C).
MS211 Engine
STIHL single cylinder two-stroke engine
Displacement: 2.15 cu. in. (35.2 cm3)
Bore: 1.7 in. (40 mm)
Stroke: 1.1 in. (28 mm)
Engine power to ISO 7293: 1.7 kW (2.3 PS) at 9,500 rpm
Idle speed: 2,800 rpm
Maximum permissible speed with bar and chain: 13,500 rpm
Clutch: Centrifugal clutch without linings
Clutch engages at: 5,100 rpm
Crankcase leakage test at gauge pressure: 0.5 bar
under vacuum: 0.5 bar
MS211 Fuel System
All position diaphragm carburetor with integral fuel pump
Carburetor leakage test at gauge pressure: 0.8 bar
Operation of tank vent at gauge pressure: 0.5 bar
Fuel tank capacity: 9.0 fl.oz (0.265 l)
MS211 Ignition System
Electronic magneto ignition (breakerless)
Spark plug (suppressed): NGK CMR6H, Bosch USR4AC
Air gap between ignition module and fan wheel: 0.15…0.35 mm
Electrode gap: 0.02 in. (0.5 mm)
MS211 Chain lubrication
Fully automatic, speed-controlled oil pump with reciprocating piston
Oil tank capacity: 9.0 fl.oz (0.265 l)
Oil delivery rate: 7.0 cm³/min at 10,000 rpm
MS211 Weight
Dry, without bar and chain:
MS 211: 9.5 lbs. (4.3 kg)
MS 211 C: 10.1 lbs. (4.6 kg)
MS211 Cutting attachments
Rollomatic E guide bars – MS 211, MS 211 C
Reduced kickback STIHL guide bars (with green label)
Bar lengths: 30, 35, 40 cm (12, 14, 16 in.)
Pitch: 3/8″ P (9.32 mm)
Groove width: 1.3 mm (0.050 in)
Sprocket nose: 9-tooth
Actual cutting length will be less than listed bar length.
Rollomatic E Light guide bars – MS 211, MS 211 C
Reduced kickback STIHL guide bars (with green label)
Bar lengths: 35 cm (14 in.)
Pitch: 3/8″ P (9.32 mm)
Groove width: 1.3 mm (0.050 in)
Sprocket nose: 9-tooth
Saw chain 3/8″ P – MS 211, MS 211 C
Low kickback STIHL saw chain (with green label)
Picco Micro 3 (63 PM3) Type 3636
Picco Super 3 (63 PS3) Type 3616
Picco Duro 3 (63 PD3) Type 3612
Pitch: 3/8″ P (9.32 mm)
Drive link gauge: 1.3 mm (0.050 in)
Chain sprocket – MS 211, MS 211 C
7-tooth for 3/8″ P (rim sprocket, spur sprocket)
6-tooth for 3/8″ P (rim sprocket, spur sprocket)
Replace spark plug with NGK CMR6H.
Torque Tightening For Stihl MS 211 Specifications
DG and P (Plastoform) screws are used in polymer and light metal components. These screws form a permanent thread when they are installed for the first time. They can be removed and installed as often as necessary without impairing the strength of the screwed assembly, providing the specified tightening torque is observed.
For this reason it is essential to use a torque wrench when working from the Stihl MS 211 Specifications.
Stihl MS 211 Specifications information can be found in Carburetor Manuals HERE and a Stihl MS211 chainsaw workshop manual HERE. Stihl Parts list HERE a chainsaw search (magnifier icon) at top and bottom of this page, as well as a chainsaw repair help question and answer page HERE.