Stihl MS 361 Chainsaw Specifications
Stihl MS 361 Specifications for the Stihl MS361 chainsaw. Find detailed specs information for the Stihl chainsaw including engine, fuel system, Carburetor, ignition system, chain lubrication,Torque settings and cutting attachments.
Stihl MS 361 Chainsaw Specs
Stihl MS 361 Specifications Carburetor
Replace carburetor with a Walbro carb: Carburetor Model: HD-34A
MS361 Engine
STIHL single cylinder two-stroke engine
Displacement: 3.6 cu.in (59 cm3)
Bore: 1.85 in (47 mm)
Stroke: 1.34 in (34 mm)
Engine power to ISO 7293: 3.4 kW (4.6 bhp) at 9,500 rpm
Idle speed: 2800 rpm
Maximum permissible speed with bar and chain: 14000 rpm
Clutch: Centrifugal clutch without linings
Clutch engages at: 3,500 rpm
Crankcase leakage test at gauge pressure: 0.5 bar
under vacuum: 0.5 bar
MS361 Fuel System
All position diaphragm carburetor with integral fuel pump
Carburetor leakage test at gauge pressure: 0.8 bar
Operation of tank vent at gauge pressure: 0.3 bar
Fuel tank capacity: 0.69 US pt (0.325 l)
MS361 Ignition System
Electronic magneto ignition (breakerless)
Spark plug (suppressed): Bosch WSR 6 F, NGK BPMR 7 A
Air gap between ignition module and fan wheel: 0.15…0.35 mm
Electrode gap: 0.02 in. (0.5 mm)
MS361 Chain lubrication
Fully automatic, speed-controlled oil pump with rotary piston
Oil tank capacity: 0.69 US pt (0.325 l)
Oil delivery rate: 5.5 – 15 cm3 at 10,000 rpm
MS361 Weight
Dry, without bar and chain: 12.3 lbs (5.6 kg), with handle heating 12.8 lbs (5.8 kg)
MS361 Cutting attachments
STIHL reduced kickback bar (with green label) for 0.325″ and 3/8″ pitch:
Rollomatic with sprocket nose 16, 18 or 20″ (40, 45 or 50 cm)
STIHL low kickback chain (with green label) for .325″ (8.25 mm) pitch:
Rapid-Micro 2 (23 RM2, 26 RM2)
Chain Rapid-Micro C3 (23 RMC3, 26 RMC3) for 3/8″ (9.32 mm) pitch:
Rapid-Micro 2 (33 RM2, 36 RM2)
Rapid-Super C3 (33 RSC3, 36 RSC3)
Chain sprocket:
9-tooth for .325″ pitch
7-tooth for 3/8″ pitch
Replace spark plug with Bosch WSR6F, Champion RCJ6Y or NGK BPMR7A.
Torque Tightening For Stihl MS 361 Specifications
DG and P (Plastoform) screws are used in polymer and light metal components. These screws form a permanent thread when they are installed for the first time. They can be removed and installed as often as necessary without impairing the strength of the screwed assembly, providing the specified tightening torque is observed.
For this reason it is essential to use a torque wrench when working from the Stihl MS 361 Specifications.
Stihl MS 361 Specifications information can be found in Carburetor Manuals HERE and a Stihl MS361 chainsaw workshop manual HERE. Stihl Parts list HERE a chainsaw search (magnifier icon) at top and bottom of this page, as well as a chainsaw repair help question and answer page HERE.